This is the official ODOM Class Association Web Site.

One Design One Meter

         BUY AN ODOM (link)

www.odomyachts.com 

ODOM BOAT REGISTRATION

http://www.theamya.org/boats/boat_reg_form.php

 

CLASS RULES

ODOM_Rules.pdf

CLASS MEASUREMENT FORM

ODOM_Measurement_Cert_2012.pdf

 

COA BOARD 
 
John Ebey
San Rafael, CA

Tony Johnson
Excelsior, MN

Jeff Hallet
Neenah, WI

Larry Wheeler
Minneapolis, MN

John Ebell
Annapolis, MD

Denny Hanson
Boulder, CO


 Jess Atkinson (Chairman)
3009 Fillmore St.
Alameda CA 94501
(510) 769-1932
odom@theamya.org

 

_______________________

Web Site Admin: Jess Atkinson

atkinfun@yahoo.com

Events

Latest Activity

CLIVE DAEM is now a member of ODOM USA
7 hours ago
ron locke replied to Al Cabito's discussion Horizon AR400 Receiver
"most receivers(rx) can not handle 7.4 volts. the servos may or may not handle it but most can not. the 7.4 is the nominal voltage. real voltage will be 8+ volts. get a voltage reduction device and place it between the battery and the rx. these…"
Friday
Al Cabito replied to Al Cabito's discussion Horizon AR400 Receiver
"Thank you...you have confirmed my assessment and I'll proceed with your recommendation al"
Tuesday
Gary Tschautscher replied to Al Cabito's discussion Horizon AR400 Receiver
"Given the high Current Drain, this servo might overload the receiver power/voltage regulator. It is unlikely the battery is causing any problems for you, as both the receiver and servo are rated adequately. A fully charged 2 cell lipo will be at…"
Tuesday
Al Cabito posted a discussion

Horizon AR400 Receiver

I have gone through 3 AR400's receivers so far.  The first stopped working,  The second overheated.  The third was overheating when I unplugged it.  I have a "Flight Power" lithium 7.4v battery and a HS7550Th Servo with the following specs:Voltage Range4.8V - 7.4VNo-Load Speed (7.4V)0.13 sec/60°Stall Torque (6.0V)402oz/in. (29kg.cm)Stall Torque (7.4V)486oz/in. (35kg.cm)Max PWM Signal Range (Standard)750-2250μsecMax Travel (out of box)120°Max Travel (reprogrammed normal res)198°Max Travel…See More
Monday
thomas macdonald is now a member of ODOM USA
Feb 17
Roger Fish is now a member of ODOM USA
Feb 12
Gary Tschautscher replied to Reg claytor's discussion ODOM specs
"Here is a link to the ODOM sales site. There is quite a bit of information which should help you out. https://odomyachts.com/models/ Important: Read carefully, some of the instructions/dimensions will be different from your older boat, as there…"
Feb 7
Reg claytor posted a discussion

ODOM specs

I am quite new with my ODOM bought it new from Adrian at his little shop a few years ago it was one of his last ones I was wonde5ring where I could get specs for setting it up rigging specs sail specs Thank You, Reg ClaytorSee More
Feb 3
Reg claytor is now a member of ODOM USA
Feb 3
Jess Atkinson posted a discussion

Passing of Adrian Olson

Hello everyone,I am sad to say that builder designer Adrian Olson past away Monday at his home in Fresdom California, he was with his family, he experienced a fatal hart attackHe made a great and positive contribution to RC sailing. We will all miss himSee More
Feb 2
Jim Tarr commented on Ken Campbell's video
Thumbnail

ODOM Sail Pts 4 Dec 11

"Great videos,using these at our was my in grand junction, co to help beginner sailors see what they have to pick up on to sail in competition. I watch them over and over to try aND pick up on better strategies for moving up in the fleet. Great job.…"
Jan 31
Dave James posted a discussion

Rules

There was a mention in the last issue of Model Yachting that the ODOM class was going to either make changes to or clarify the rules regarding sails. Any progress?See More
Jan 25
Profile IconJohn Dodge and Hal Mooz joined ODOM USA
Jan 21
chris sullivan liked ron locke's discussion boats for sale
Jan 21
Profile IconRobert Gallagher, Bob Buckley and Steve Mueller joined ODOM USA
Jan 18
ron locke posted a discussion

boats for sale

i added two boats for sale today. go to marketplace to see the remarks. rlSee More
Jan 16
Arthur L Howard is now a member of ODOM USA
Jan 16
Ken Campbell is attending Jess Atkinson's event

Region 5 championship at Sahuarita, AZ

February 11, 2017 at 8am to February 12, 2017 at 3pm
 Hello Everyone . I received the invite to the Region 5 championship today.. It is open to everyone... Here is the letter from the commodore of Green valley YC.ODOM%202017%20Region%205%20NOR%20%281%29.docx…See More
Jan 10
David HAMMETT replied to David HAMMETT's discussion Mast Tubes and where to get them in the group BUILDERS PAGE
"Many of phone calls and emails."
Dec 29, 2016
 

ODOM USA: WELCOME

This is a place where ODOM owners can share all things ODOM from coast to coast. Keep up with all the latest news from all the ODOM fleets across the nation. 


If you're an ODOM owner sign up, create profile under “MY PAGE” and/or create a “GROUPS” page for your club. If your Building your boat look at the Builders Page under “GROUPS” and you'll find helpful tips. Want to know where ODOM events are across the country look under "EVENTS"
. Also checkout “LINKS” which is a directory for everything you need. And use the “FORUM” to open a discussion on issues you need to solve and tell everybody what you think.


The ODOM is a one design radio controlled yacht one meter in length; 7 lbs 6 oz minimum weight;  600 square inches of sail area.


Thanks for your continuing contribution to the ODOM National website.


Jess Atkinson

Odom Class Secretary

odom@theamya.org

 

Photos

Loading…
  • Add Photos
  • View All

Videos

  • Add Videos
  • View All

Forum

Horizon AR400 Receiver

Started by Al Cabito. Last reply by ron locke on Friday. 3 Replies

I have gone through 3 AR400's receivers so far.  The first stopped working,  The second overheated.  The third was overheating when I unplugged it.  I have a "Flight Power" lithium 7.4v battery and a…Continue

ODOM specs

Started by Reg claytor. Last reply by Gary Tschautscher Feb 7. 1 Reply

I am quite new with my ODOM bought it new from Adrian at his little shop a few years ago it was one of his last ones I was wonde5ring where I could get specs for setting it up rigging specs sail…Continue

Passing of Adrian Olson

Started by Jess Atkinson Feb 2. 0 Replies

Hello everyone,I am sad to say that builder designer Adrian Olson past away Monday at his home in Fresdom California, he was with his family, he experienced a fatal hart attackHe made a great and…Continue

Rules

Started by Dave James Jan 25. 0 Replies

There was a mention in the last issue of Model Yachting that the ODOM class was going to either make changes to or clarify the rules regarding sails. Any progress?Continue

 
 
 

© 2017   Created by Jess Atkinson.   Powered by

Badges  |  Report an Issue  |  Terms of Service